Call 01473 27 66 77 for Assistance with your Underfloor Heating Project

Din Rail Thermostats


DeviReg 700 Series

The Devireg 700 series is primarily regulate your accumulating heating system or other places where it may be advantageous to switch on the heat at times with low-tariff electricity, according to outside temperature and the "quantity" of stored heat.

This series is electrical thermostats used for DIN rail mounting. The maximum load of the relay is 10 amp. (2500 W by 250 V).

The Devireg 751-754 are all slave units, which controls different rooms.

Devireg 751 controls one room
Devireg 752 controls two rooms
Devireg 753 controls three rooms
Devireg 754 controls four rooms

The devireg 751-754 units can only be operated in connection with the devireg 700.

The temperature in the room can be regulated up and down individually according to a percentage deviation from normal. This can be done for both the day and the night period.

Also the maximum temperature in each room can be set from the slave units.

Devireg 700 Series
Product Features
  • DIN rail mounting
  • Accumulating heating systems
  • Master/slave connection one master can control up to 400 different rooms/zones.
  • Low tariff system

Downloads

Model Width Sensor Temperature
Setting
Primary Use Inductive Load  
710 Single Zone
750 52 mm Outdoor sensor and wire floor sensor with NTC; 15kO / 25C +5 to +55C Master with one built-in slave 1 A
751 36 - 72mm Room with NTC; 15kO / 25C +5 to +55C Slave for 1 Room 1 A Available upon request
752 36 - 72mm Room with NTC; 15kO / 25C +5 to +55C Slave for 2 Room 1 A Available upon request
753 36 - 72mm Room with NTC; 15kO / 25C +5 to +55C Slave for 3 Room 1 A Available upon request
754 36 - 72mm Room with NTC; 15kO / 25C +5 to +55C Slave for 4 Room 1 A Available upon request
 

DeviReg 330 Series

The devireg 330 series is a simple electrical thermostat used for DIN rail mounting. The maximum load of the relay is 16 amp. (4000 W by 250 V).

These thermostats regulate your heating system fast and accurate.

They can control both heating, air-condition and ventilation, and can be used for both indoor and outdoor applications.

The devireg 330 series covers 5 different temperature areas.

devireg 330, -10 to +10C, is often used for frost protection or cooling. The cooling application is for example to be found in cold stores. Here you can also find a frost protection system heating system - around the doors, so they always can be opened.

The frost protection system can be used for stairs, garages, roof gutters, traffic areas, pipes etc.

devireg 330, -10 to +10C should always be connected with a wire sensor place in the area of heating/cooling.

Please note that the set back function is not available in this version of devireg 330.

Please note when connected for cooling the maximum load of the relay is 10 amp. (2500 W by 250 V)!!

Devireg 700 Series
Product Features
  • DIN rail mounting
  • Temperature adjustment button
  • Light indicators:
  • Red: heating up the floor
  • Green: Temperature according to the settings, and no heat on

Downloads

Model Width Sensor Temperature
Setting
Primary Use Inductive Load  
330 36 mm Wire with NTC; 15kO / 25C -10 to +10C Frost Protection 3A
330 36 mm Wire with NTC; 15kO / 25C +5 to +45C Floor Protection 3A
330 36 mm Wire with NTC; 15kO / 25C +15 to +30C Room Protection 3A Available upon request
330 36 mm Wire with NTC; 15kO / 25C +30 to +90C Pipe Heating 3A
330 36 mm Wire with NTC; 15kO / 25C +60 to +160C Pipe Heating Can be used in High Temperature Areas. 3A Available upon request
 

DeviReg 316

The Devireg 316 is a multipurpose thermostat used for both indoor and outdoor applications. The total temperature range is between -10C up to +50C, with both adjustable minimum and maximum temperature.

The thermostat is for mounting in a DIN rail and it is regulated by a NTC sensor.

With the minimum temperature function Devireg 316 is the right product for small outdoor applications. If the temperature gets very low (below -10C) it is very unlikely to snow. Therefore the Devireg 316 switch off the heating system below the set minimum temperature saving the end user for unnecessary energy consumption.

Devireg 700 Series
Product Features
  • DIN rail mounting
  • Maximum temperature adjustment button
  • Minimum temperature adjustment button
  • Adjustable set-back
  • Hysteresis adjustment button
  • Light indicators:
  • Red: system heating up
  • Yellow: below minimum temperature and is not heating

Downloads

Model Width Sensor Temperature
Setting
Primary Use Inductive Load  
316 52 mm NTC; 15kO / 25C -10 to +50C Multi-Purpose 3 A Available upon request